Have BM4000 looking to get Wifi Thermostat with Humidity control

Post your questions and comments here.
scottz
Posts: 4
Joined: Tue Apr 12, 2016 11:07 pm

Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by scottz »

I have a Tempstar T9MPD100J14A2 Furnace
Skuttle 2000 Humidifier
Broan HRV100H air exchanger w remote control for fan speed and condensation control (located on main floor)
Cheap Air conditioner (make/model not handy)
EWC BM4000 (BM2000+EX-2) controlling 3 zones

I would like to upgrade form my one of my LUX 4wire thermostats to a Honeywell TH8321WF1001 Wifi Vision Pro 8000 with Stages l thermostat so I qualify for power company rebates and credits. I would like to be able to control my humidifier and air exchanger condensation controls if possible.

Which controller board would you recommend?
scottz
Posts: 4
Joined: Tue Apr 12, 2016 11:07 pm

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by scottz »

Image
Paul Z.
Posts: 216
Joined: Thu Dec 08, 2011 3:05 pm

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by Paul Z. »

Give the office a call have a few question 18004463110X490.
scottz
Posts: 4
Joined: Tue Apr 12, 2016 11:07 pm

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by scottz »

I purchased the BMPLUS3000 and wired the new unit the same as the older control board. I did this in early May. Everything worked great during the cooling season.

Now when any of the thermostats call for heat
The LED lights up for that zone
The furnace blower fan comes on however the furnace never ignites.
After the fan runs for about 90 seconds, the blower fan shuts off and the W1/B light comes on, on the BMPLUS3000.

All during this time the Furnace LED is alternating between bright/dim which means it is opportunity normally.

Can you think of anything obvious I may have missed?
scottz
Posts: 4
Joined: Tue Apr 12, 2016 11:07 pm

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by scottz »

As a continuation of my above post. After about 20 minutes passed, the furnace ignited, then about 30 seconds went by and the fan kicked in. At this time I noticed the W1/B and W2/E LEDs illuminated on the BMPlus3000. It also shows two zones open (1 and 3).


Image
Mozis
Posts: 1
Joined: Sat Dec 10, 2016 3:32 am

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by Mozis »

So did it pretty much fix itself then?
Last edited by Mozis on Thu Dec 07, 2023 2:31 pm, edited 4 times in total.
Wencent
Posts: 1
Joined: Wed Mar 20, 2019 8:52 am

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by Wencent »

scottz wrote: Mon Nov 14, 2016 5:49 pm As a continuation of my above post. After about 20 minutes passed, the furnace ignited, then about 30 seconds went by and the fan kicked in. At this time I noticed the W1/B and W2/E LEDs i noticed this v tight gel illuminated on the BMPlus3000. It also shows two zones open (1 and 3).


Image
So did it pretty much fix itself then?
goodboy
Posts: 2
Joined: Wed Dec 29, 2021 5:13 am

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by goodboy »

You made some decent points there. I appeared on the web for the issue and located most individuals will associate with with your website.
look at this web-site
goodboy
Posts: 2
Joined: Wed Dec 29, 2021 5:13 am

Re: Have BM4000 looking to get Wifi Thermostat with Humidity control

Post by goodboy »

Thank you so much for the information very nice blog
What do apartment inspectors look for?
Post Reply