Search found 30 matches
- Fri Jun 09, 2023 4:04 pm
- Forum: Help and Advice
- Topic: EWC's UT3000 & ComfortBridge equipment compatibility
- Replies: 14
- Views: 23911
Re: EWC's UT3000 & ComfortBridge equipment compatibility
1stbscout, Sounds like you had a real adventure getting this equipment to work... Actually, the term ComfortNet is what Goodman uses to identify their Climate Talk family of equipment. So they are not different...Goodman's ComfortNet family is utilizing the Climate Talk open protocol. In a fully ...
- Thu Jan 12, 2023 12:11 pm
- Forum: Help and Advice
- Topic: EWC's UT3000 & ComfortBridge equipment compatibility
- Replies: 14
- Views: 23911
Re: EWC's UT3000 & ComfortBridge equipment compatibility
That is correct...The ComfortBridge indoor unit simply needs a W signal for Heat or a Y signal for Cool.
This is the case, even if the ComfortBridge system is a Heat Pump.
John
This is the case, even if the ComfortBridge system is a Heat Pump.
John
- Thu Jan 05, 2023 9:10 am
- Forum: Help and Advice
- Topic: EWC's UT3000 & ComfortBridge equipment compatibility
- Replies: 14
- Views: 23911
Re: EWC's UT3000 & ComfortBridge equipment compatibility
Kevin, First off, the UT3000 can be used in non-communicating mode, to operate your ComfortBridge family of equipment, if full communicating mode cannot be achieved. I assume your Outdoor unit is also communicating? Perhaps a two stage unit or an Inverter? All communicating outdoor units are still ...
- Wed Jul 20, 2022 11:59 am
- Forum: Help and Advice
- Topic: EWC's UT3000 & ComfortBridge equipment compatibility
- Replies: 14
- Views: 23911
Re: EWC's UT3000 & ComfortBridge equipment compatibility
Joylove, Thanks for the equipment specs...They may come in handy. As you may or may not know, we have been working with Daikin on the CT protocol, for their FIT line of communicating equipment and the Daikin One communicating thermostat. As a result, the UT3000 firmware evolves to maintain ...
- Mon Jul 18, 2022 10:25 am
- Forum: Help and Advice
- Topic: EWC's UT3000 & ComfortBridge equipment compatibility
- Replies: 14
- Views: 23911
Re: EWC's UT3000 & ComfortBridge equipment compatibility
Joylove, It's great that your ComfortBridge system can be fully controlled by the UT3000. We have received some reports of successful ComfortBridge installations using our patented UT3000 controller. However, these jobs are very few and far in between. Successful UT3000/ComfortBridge (fully ...
- Mon Jan 10, 2022 11:18 am
- Forum: Help and Advice
- Topic: EWC's UT3000 & ComfortBridge equipment compatibility
- Replies: 14
- Views: 23911
EWC's UT3000 & ComfortBridge equipment compatibility
Recently, we have received numerous tech calls from frustrated Contractors who cannot achieve control (communication) between the Ultra-Zone UT3000 zone controller and Goodman "ComfortBridge" rated HVAC equipment. This is because ComfortBridge "indoor units" are designed to work with "legacy" non ...
- Fri Oct 22, 2021 3:19 pm
- Forum: Help and Advice
- Topic: Damper Motors Compatible With EcoNet Zone Controller
- Replies: 1
- Views: 4056
Re: Damper Motors Compatible With EcoNet Zone Controller
Sir, Your MA-ND5 motor actuators are compatible with Rheem/Ruud EcoNet communicating HVAC systems. The MA-ND5 motor actuator is a "floating Point" actuator that modulates via the EcoNet zone controller, as it receives commands from the Primary/Master thermostat for all connected zones on the network ...
- Wed Jun 09, 2021 2:25 pm
- Forum: Help and Advice
- Topic: UT-3000 with bypass humidifier
- Replies: 1
- Views: 5944
Re: UT-3000 with bypass humidifier
meassick, Sorry for the late response. We have had extremely high tech call volume and have not paid sufficient attention to the forum. Sir, it appears that someone has programmed one or both CTK04's to "humidify" without heat!....This is a function in the "Installer Menu" of each CTK04 thermostat ...
- Wed Jun 09, 2021 2:17 pm
- Forum: Help and Advice
- Topic: HVAC not responding and the BMPlus 3000 LED's are off
- Replies: 5
- Views: 10098
Re: HVAC not responding and the BMPlus 3000 LED's are off
tnormile, Sorry for the late response. We have had extremely high tech call volume and have not paid sufficient attention to the forum. Sorry your BMP failed and it appears the BMP was powered via the same 24vac transformer in the furnace, rather than a dedicated transformer, as specified in the ...
- Wed Jun 09, 2021 1:42 pm
- Forum: Help and Advice
- Topic: Swapping EWC-ST-2E for NCM-300
- Replies: 1
- Views: 5942
Re: Swapping EWC-ST-2E for NCM-300
Eddie23, Sorry for the late response...We have had extremely high tech call volume over the last 6 months and have not paid sufficient attention to the forum. You don't have to use the "SAS" supply air sensor but we highly recommend it. If you decide to install and use it, drill the hole in the ...